Quick start user manual
Section 1
The warnings in this manual must be observed together with the "USER MANUAL - Section 2".
Le avvertenze nel presente manuale devono essere osservate congiuntamente al “MANUALE D’USO - Sezione2”.
Die Warnungen in diesem Handbuch müssen in Verbindung mit der "BEDIENUNGSANLEITUNG - Abschnitt 2" beobachtet
werden”.
Les avertissements specifiés dans ce manuel doivent être respectés ainsi que les "CARACTERISTIQUES TECHNIQUES -
Section 2"
Las advertencias del presente manual se deben tener en cuenta conjuntamente con las del “MANUAL DEL USUARIO” -
Sección 2”.
A.E.B. Industriale Srl Via Brodolini, 8 Località Crespellano 40053 VALSAMOGGIA BOLOGNA (ITALIA)
3) Amplifier control panel:
a) Connect the audio input [1]. In case of dynamic
microphone, select “MIC” in input sensitivity switch [3],
otherwise select “LINE”. Adjust the Input Attenuation
level [2].
b) If you need to send the audio signal to a second
speaker, connect the “Output Link” [4] to the Input on
[1] of another W10 (for example) using a cable with
XLR (balanced) connector.
c) Set properly the DSP Coverage Preset [5], choosing
between:
1–DEFAULT
2–CLOSE-NARROW
3–CLOSE-WIDE
4–FAR
120 HPF – HPF 120 Hz – (a high-pass filter
which can be applied to 2, 3, 4 positions)
d) In case of remote control, connect the proper Data
Input [6] to the hardware remote controller (RDNet
Control 2 or RDNet Control 8) with cables equipped
with etherCON connectors. Then connect the Data
Output [6] to the Data Input [6] of a second w10, and
so on. When the RDNet network is on and it has
recognized the connected device, the LED “Link” [6] is
on. The other LED [6] “Active” start blinking when
there is the presence of data transmission, the
“Remote Preset Active” advise that all the local
controls set on the amplifier panel (level, DSP presets,
etc.) are by-passed and controlled remotely by the
software AURORA NET. See also RDNet Control 2,
Control 8 and AURORA NET user manuals for further
information.
e) Plug the mains Input [9] and Link [10] (powerCON
True1) cables. The Signal/ON led [7] starts blinking,
signaling the presence of audio signal.
WARNING
The speaker is supplied with a mounted fuse for operation within the
220‐240V~ range. If you need to operate in the 110‐120V~ voltage range:
1. Disconnect all connections, including the power supply.
2. Wait for 5 minutes.
3. Replace the fuse with the one provided in the package
for the 100‐120V~ range
information about the system and available accessories.
ulteriore informazione sul sistema e sugli accessori disponibili.
Für weitere Informationen und verfügbares Zubehör lesen sie bitte die
vollständige Bedienungsanleitung unter
Vérifiez le manuel de l'utilisateur complet sur www.dbtechnologies.com
pour des informations complémentaires du système et des accessoires
disponibles.
Compruebe
el
manual
de
usuario
completo
sobre
www.dbtechnologies.com para la información adicional sobre el sistema
y accesorios disponibles.
1–Balanced input (XLR connector type)
2–Input attenuation control
3–Input sensitivity type switch (MIC/LINE)
4–Balanced output Link (XLR connector type)
5–Coverage/filter preset rotary
6–RDNet DATA IN/OUT
7–CONTROL LEDs
8–USB DATA SERVICE
9–Auto-range Mains Input
10–Mains Link
11–Mains Fuse
Technical Data
Processor
Speaker Type: 2-way wooden wedge monitor
MD-HF: 4 " Exit (NEODYMIUM)
HF voice coil: 1”
Controller: 28/56 bit DSP
AD/DA converter: 24 bit/48 kHz
Advanced DSP function: FIR Filters
Limiter: Peak, RMS, Thermal
Controls: 1 DSP rotary encoder, 1 input sensitivity
encoder, status LED, RDNet status LED
LF: 10”
LF Voice Coil: 2.5”
SPL: 126 dB
Frequency response (-10 dB): 58 – 15000 Hz
Frequency response (-6 dB): 68 – 14000 Hz
Crossover frequency: Steering depending
Input/Output
Mains/link connections: powerCON® TRUE1 type
Signal Input/Link: Balanced XLR type
RDNet connections: Data in, Data out
Daisy chain power connection (max number of W10): 20
(1+19) (220-240V~) / 14 (1+13) (100-120V~)
Amplifier
Amp Technology: Digipro® G3 Auto-range
Amp Class: Class-D
RMS Power: 400 W
Mechanics
Peak Power: 800 W
Housing: Wooden box
Grille: Full grille
Operating voltage:
220-240V~ (50-60 Hz) or 100-120V~ (50-60 Hz)
Auto-range Mains
Width: 450 mm (17.71 in)
Height: 165 mm (6.49 in)
Depth: 480 mm (18.89 in)
Weight: 13,7 kg (32 lbs.)
Download the complete
user manual on:
EMI CLASSIFICATION
According to the standards EN 55103 this equipment is designed and suitable to operate in E3 (or lower E2, E1) Electromagnetic environments.
FCC CLASS B STATEMENT ACCORDING TO TITLE 47, PART 15, SUBPART B, §15.105
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
4. Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the
equipment.
WARNING: Make sure that the loudspeaker is securely installed in a stable position to avoid any injuries or damages to persons or properties.
For safety reasons do not place one loudspeaker on top of another without proper fastening systems. Before hanging the loudspeaker check
all the components for damages, deformations, missing or damaged parts that may compromise safety during installation. If you use the
loudspeakers outdoor avoid spots exposed to bad weather conditions.
Contact dB Technologies for accessories to be used with speakers. dBTechnologies will not accept any responsibility for damages caused by
inappropriate accessories or additional devices.
Features, specification and appearance of products are subject to change without notice.
dBTechnologies reserves the right to make changes or improvements in design or manufacturing without assuming any obligation to change
or improve products previously manufactured.
|