P R O D U C T D ATA S H E E T
ACTUATOR
LA32
Features:
• 24 V DC permanent magnet motor
• Thrust up to 6000 N (with ball screw)
• Stainless steel piston rod
• High-strength plastic housing protects motor
and gears
• Elegant and compact design with small
installation dimensions
• Protection class: IPX1
• Colour: black
• 2250 mm straight cable with 6.3 mm jack plug
• Low noise level: 46 dB (A); measuring method
DS/EN ISO 3746, actuator not loaded
• LA32K with ball screw and double-acting brake
(i.e. push and pull / both directions)
Options:
• Protection class: IPX5 or IPX6
• Reed-switch for exact positioning (8 pulses per
spindle revolution)
• LA32 with 5 mm pitch F: Manual quick release
• LA32 with 5 mm pitch FH: Manual quick release
with dampened movement
• Mechanical splines function (push only)
• Electrical splines function, built-in micro-switch in
back fixture, the actuator can therefore only be
used for push. (Only with 01 and 02 back fixture)
• LA32K with ball screw and double-acting brake
(i.e. push and pull/both directions)
• LA32KAS with ball screw and safety nut
• LA32KSM with ball screw, safety nut and
mechanical splines
• Available with 0.2 m or 0.4 m coiled cable
• LA32JKSM available with 2-speed facility for the
LINAK JUMBO SYSTEM
• CS32; electronic limit switch (built-in)
Usage:
• Duty cycle: Max. 10% or 2 minutes continuous use
followed by 18 min. not in use
The LA32 is a powerful actuator that can be supplied
with a ball screw spindle to give outstanding perfor-
mance. The ideal choice for a wide range of applica-
tions including adjustment of hospital beds.
• Ambient temperature +5° to +40° C
• For use with LINAK control boxes CB8, CB12, CB14
and CS16 PCB or internal CS32 PCB
• Should LA32 be used with a non LINAK control
unit, please ask the nearest LINAK representative
for further details
The LA32 has many special options including a safety
nut, splines, quick release (F) and an optional protec-
tion class up to IPX6 standard.
Accessories::
• CS16; electronic limit switch
• Optical encoder
• SLS: safety limit switch
Dimension
+0.1
0
30
Ø10.1
+0.2
Ø10.1
0
11
51
24.5
13
204
30
S
S + 173
28
+0.2
0
Ø12.1
18
36
LINAK A/S
LA32001B
01
S + 173: (with/without safety nut)
02
05
06
Installation dimensions:
(Min. install dim. 273 mm) S + 181: (LA323. with/without safety nut)
S + 184: with splines
S + 198: with splines and safety nut
S + 210: LA32K, LA32KAS, LA32 with safety nut
S + 215: with brake
3D view of the back fi xture.
(here type “01” is shown.
Drawing no.: 0321200
S + 267: LA32KSM
LA32 with quick release:
05
01
02
06
Drawing no.: LA32F001C
Install. dimensions:
S + 173: LA32.F
S + 196: LA32FH
Technical specifications:
Type
Push
321xxx+00xxx4xx
322xxx+00xxx4xx
3000
3000
(2000N)
13.6/8.5
(2000N)
4.5
322xxx+40xxx4xx
32Kxxx+x0xxx4xx
32Kxxx+10xxx4xx
32Kxxx+30xxx4xx
3000
#
#
328xxF+x0xxx4xx
32Kxxx+30xxx3xx
9.5
15/6.5
7500
(7500N)
(7500N)
The above measurements are made in connection with a CB12, the LA32JKSM with a CBJ1 high speed.
P
= Stroke lengths where potentiometer is possible as standard
* LINAK control boxes are designed so that they will short-circuit the motor terminals (poles) of the actuator(s) when the actuator(s) are not
running. This solution gives the actuator(s) a higher self-locking ability. If the actuator(s) are not connected to a LINAK control box the termi-
nals of the motor must be short-circuited to achieve the above mentioned self-locking ability.
# = Not with spindle potentiometer (stroke length max. 220 mm)
K
= Ball screw
KAS = Ball screw with safety nut
KSM = Ball screw with splines and safety nut
R
= Reed-switch
F
= Manual quick release
FH
= Manual quick release with dampened movement
KAS and KSM are only available on LA32K (with ball screw)
Graphs:
LA32 current v´s load
LA32 speed v´s load
16
5
4,5
4
6mm pitch
14
6mm pitch
Ball screw
5mm pitch
3mm pitch
12
3,5
3
10
8
5mm pitch
3mm pitch
Ball screw
2,5
2
1,5
1
0,5
0
6
4
2
0
1000
2000
3000
4000
5000
6000
0
0
1000
2000
3000
4000
5000
6000
Thrust (N)
Thrust (N)
Measurements are made in connection with a CB12
Terms of use
The user is responsible for determining the suitability of LINAK products for specific application.
LINAK takes great care in providing accurate and up-to-date information on its products.
However, due to continuous development in order to improve its products, LINAK products are
subject to frequent modifications and changes without prior notice. Therefore, LINAK cannot
guarantee the correct and actual status of said information on its products.
While LINAK uses its best efforts to fulfil orders, LINAK cannot, for the same reasons as
mentioned above, guarantee the availability of any particular product. Therefore, LINAK reserves
the right to discontinue the sale of any product displayed on its website or listed in its catalogues
or other written material drawn up by LINAK.
All sales are subject to the Standard Terms of Sale and Delivery for LINAK. For a copy hereof,
please contact LINAK.
|